Homemade pizza barrel oven plans


This project involves quite a deal of bricklaying, so if you are not experienced, the base structure will give you plenty of opportunity to hone your skills. And if it’s too messy, you can always bag it to match the oven.


The simplest way to build a pizza oven is with a precast kit for about $2300 (1100mm diameter internally) which consists of precast concrete dome sections that simply slot together, or make a similar sized dome for about $1500 using plain fire bricks over a sand form. Both need to be heavily insulated, a flue and an oven door.

To build a large tunnel oven (1200 x 900mm internally) such as this with door and flue arches, will cost about $2600 in refractory materials. On top of the oven you will need to add the cost of the base structure and the outside render (about $750), and the peel (for handling the pizzas) and the ash rake (about $200 for the two).

It’s important to insulate the oven well, as temperatures can peak well above 450°C inside and you need to sustain high temperatures inside as you cook, at the same time keeping the outside cool enough to avoid accidental burning.

The external dimensions of this oven are 2 x 1.6m while the internal cooking area is about 1200 x 900mm. The extra space is taken up in fire bricks and insulation required to keep the oven hot – the walls are around 245mm thick! Wood-fired pizza ovens do their cooking by heat radiating from the thermal mass of the bricks. Before you start cooking, you have to set a fire to heat up the bricks in the oven. Once the bricks reach the required temperature, the inside surface of the bricks turns white. You then push the coals to the sides so that heat is maintained, shut the door and you’re ready to cook. When you’re cooking limit the air flow so the inside stays hot. 

Making the Pizza Oven

The Base

As the pizza oven will weigh several tonnes when complete, it needs a solid base.

Supplies

Following are the items that will be required for making the base.

- 100 x 50mm timber for formwork

- 1 piece of 1900 x 1500 F82 steel mesh

- 0.35 cubic meters of 20Mpa concrete

- 325 of dry pressed (solid) bricks

- 3 bags mortar

- 25 wire ties

- 1 of 75 x 10mm (or 85 x 8mm ribbed) x 1080mm galvanised steel lintel

- 2 or 3 of 75 x 10 x 1370mm galvanised steel lintels

- 2 sheets of 1780mm long corrugated iron

- 1 piece of 1290 x 1680mm F82 steel mesh

- 6 of 1680mm lengths of Y12 steel bars

- 0.3 cubic m of concrete (ready-mixed or mix your own)

Constructing the Base (Step by Step)

Step - 1

This oven has a 1600 x 2000mm concrete base, 100mm thick, reinforced with F82 steel mesh. It is simply formed using 100 x 50mm timbers well staked to the ground and levelled. It easiest with this quantity of concrete (allow 0.35 cubic metres) to have a mini load delivered. Pour in half the concrete, rake level and put in the steel mesh. Add the remainder of the concrete, screed level, float, let set and wet cure for a few days.

Step - 2

Mix a standard brickie’s mortar of 1 part cement with 5 parts sand and Bycol added (or use bags of mortar mix), and lay 2 courses of bricks around the perimeter of the slab leaving a 900mm opening at the front (one of the 1600mm slab edges). Add corner bricks to form internal piers and an engaged pier half way along each long side.

Step - 3

Start building up the corners the equivalent of 11/2 bricks in each direction and offset the internal engaged piers about 15mm from the outer bricks, holding them in place with wire ties. Keep building up the corners and piers until they are 6 courses high. While a standard mortar joint is 10mm thick, in this case it’s a good idea to make a 5mm thick joint for the internal piers, so the top of the piers will be lower that outside brickwork, and give the top suspended slab greater depth.

Step - 4

Infill between the corners with brick panels set 15mm back from the front edge of the bottom two courses. This gives the brickwork an attractive recess which can be rendered or bagged later to match the upper structure.

Step - 5

Complete the brickwork of all the recessed areas to the top of the corners, then place a 75 x 10mm plain or 85 x 8mm ribbed lintel across the opening so it has 90mm bearing on both sides. Add a temporary timber prop under the centre of the lintel, then lay two more courses of brickwork in line with the brick corners at the base, and stopping the internal corner bricks and engaged piers one brick from the top. Clean up the brickwork with a stiff brush, and let set for a day or two.

Step - 6

Place another lintel across the front opening on the corner bricks and a third across the back corner bricks. Build a temporary loosely stacked pier of bricks in the centre to the same height as the piers and add another optional lintel across the centre. Place corrugated steel across the lintels to fill the space and act as bottom formwork. Cut F82 steel reinforcing mesh so it will be about 40-50mm short at each side. Also cut 6 Y12 bars to further reinforce the suspended slab.


Step - 7

Make a mix of standard concrete (1 part cement, 2 parts sand and 4 parts aggregate) or order more ready-mixed concrete. Pour in half the concrete, lay in the steel mesh and the 12mm steel bars as reinforcing across the piers and centre.


Step - 8

Fill the slab to just over the top surface of the bricks, and with a helper, screed the concrete with a chopping action to eliminated air bubbles and smooth the top surface to the level of the brickwork. Finish with a wooden trowel for a smooth finish. Let set and cure wet for a few days.


Oven Formwork

Supplies
EndsSlatsCentre support
Material19mm plywood70 x 19mm pine19mm plywood
Main chamber900 x 630mm (2)1162mm (19)862 x 611mm
Door arch480 x 400mm (2)192mm (12)nil
Flue arch605 x 470mm (2)192mm (14)nil

Construction

Step - 9

Construct formwork for the main chamber using the diagram to form the shape of one end. The numbers around the perimeter indicate the wedge brick sizes to be used to form the arch in metric (on outside) and Imperial (on inside) units. Cut out the end with a jigsaw, trace and cut out a second end, then screw the slats between the ends so there are only a few narrow gaps between the slats. Only screw on from the outside as the screws need to be removed to collapse the formwork later. Cut a centre support to loosely sit under the slats in the middle. Lift on the platform so it is centred between the sides and 260mm from the back. Scratch the position on the concrete, lift the formwork, then loosely locate the centre support under the slats and lower the formwork. Make the door and flue arch forms the same way, but without the centre support, ready for use later on. Scratch their position on the concrete as well.

The Oven

Supplies

Note: the quantities given are for this oven. Ask your supplier to calculate exact quantities needed for your sized oven. The curved arches are formed using straight and two different sizes of wedge shaped arch bricks. When ordering your materials, let the supplier know the arch sizes or better still have the templates with you, as you can then work out which combination of arch bricks will suit best.

Refractory materials

- 98 of 230 x 115 x 75mm straight (s/s) refractory bricks

- 110 of 230 x 115 x 75/63mm (or 21/2 inch) side arch bricks

- 60 of 230 x 115 x 75/51mm (or 2 inch) side arch bricks

- 5 of 20kg drums of Tufset Super refractory mortar (for thin joints)

- 5 of 25kg bags of Fireplas refractory mortar (for thicker joints)

- 3 of 1000 x 500 x 50mm Calsil (calcium silicate) boards

- 16 of 300 x 300 x 50mm refractory tiles

- 1 of 900 x 200mm diameter stainless steel flue plus cap

- 8 of 50mm Duraback batts

- 10 of 10kg bags of Insulite 1000L vermiculite render


You will also need

1 roll of 20mm chicken wire; steel door (made to suit); sharp washed sand; cement; oxide; Bondcrete; Silasec. For cooking you will also need an ash rake and wooden or metal peel.



Refractory materials Refractory or fire bricks are specialty bricks with a high alumina content. They are made to withstand the high temperature and cooling cycles that ovens and furnaces undergo. Ordinary house bricks, while fired at high temperatures, will not withstand these conditions.


Construction

Step - 10

Check that main chamber formwork is correctly located. Using a pre-mixed refractory mortar designed to take high temperatures, butter each brick as you are about to lay it with a thin bed and lay two courses of straight refractory bricks, marked s/s on the templates, along each side of the formwork. The mortar goes off fairly quickly (2-3 hours) so needs to be used quickly before it skins. Limit the thickness of mortar joints to a maximum of 3mm, ideally 1-3 mm, as the mortar will shrink and you will end up with a tighter oven with less cracking.

Step - 11

Form the curve of the chamber using refractory side arch bricks, which are wedge shaped on their ends. Use two sizes which reduce from 75 to 63mm (21/2 inch) and from 75 to 51mm (2 inch) in combination to form the radius of the arch. The wedge-shaped bricks are laid exactly the same as straight bricks, and are supported by the form. Check for level as you build up the courses.

Step - 12

The mortar will set over about 48 hours, and even longer during wet weather, so don’t remove the formwork until mortar has set. Cover the arch with a tarp if rain threatens, as the mortar will soften again if it gets wet.

Step - 13

Strip the formwork by unscrewing the plywood ends, then knock out the centre support. Remove the slats and check for gaps in the mortar joints. Using more of the mortar, fill in any gaps, but do not render or bag the inside surface.

Step - 14

Build the back wall as a separate wall, cutting the ends of the bricks to follow the curve as you build up the courses. Make sure there is a good vertical bed of mortar between the arch and the end wall, and as this may be thicker than mortar beds, use the Fireplas mortar which can be used in wider joints. Slightly rough brick ends do not really matter as all this brickwork will be covered in insulation and rendered.

Step - 15

Cut and install sheets of calcium silicate board to fit inside the base of the oven. This board is easily cut with a handsaw and sits on the concrete loosely. Follow with the 300 x 300mm refractory tiles to form the cooking surface of the oven. Also cut and install the sheets and tiles to fit out the door and flue arches, using the scratched outline as a guide.

Step - 16

Using the small door arch formwork, build the arch of single stacked bricks on top of the refractory tiles with only straight and 75 to 51mm (2 inch) side arch bricks. Before laying the bricks make sure the arch is completely vertical on its face, otherwise the geometry of the arch will not work. Use small timber wedges under the ends to make any adjustments.

Step - 17

Fill in the gap between the door arch and the main chamber with straight bricks, cutting and shaping them to suit different curves on the two arches. As the gaps will be larger, use Fireplas refractory mortar to fill in irregular gaps. Again, this brickwork does not have to be highly accurate as the whole lot will be covered with insulation and render.

Step - 18

Before building the flue arch, make sure the door arch has set, then carefully remove any wedges and pull the form straight back. The arch should support itself. If you have trouble pulling out the form, drill some finger holes in the end to help.

Step - 19

Bring in the flue arch formwork, again checking that it is truly vertical, then start laying the arch with two courses of straight, then 63mm bricks followed by 51mm bricks. This brickwork must be neat with neat joints, as the bricks will remain exposed as a feature. Lay all the fire bricks up to the last four at the top. Cut 50mm pieces off the ends of the four top bricks, and bed them in place to allow room for fitting the flue in the centre of the arch.

Step - 20

Let the mortar set for an hour or two to gain a little strength. Squeeze the chimney slightly front to back, so that will fit between the part bricks and door arch. Cut a few more small brick wedges to fill in the gaps, then set the flue and wedges in a thick bed of mortar.

Step - 21

Use more mortar to smooth and render the flue in place. Let set, propping the flue upright if necessary. Remove the flue arch formwork so the joints can be cleaned up with a scourer and fill any empty joints. Let stand and cover with tarp for a few days to gain strength.

Step - 22

Cover the main oven and door arch with mineral wool insulation blanket, cutting it to shape with a utility knife where necessary. Wear a dust mask and gloves as some fine fibres can be released. Shape chicken wire to cover all the areas to be rendered, working the mesh up to the back of the flue arch.

Step - 23

Wearing a respirator because of the dust, mix complete bags of Insulite vermiculite render with water. Only mix full bags as the contents tend to settle and you may not get a proper mix if only a half bag is mixed. Try to achieve a mix the consistency of wet beach sand. You can try to trowel it on, although as the surface is soft and pliable, it’s easiest to pack it onto the surface by hand using gloves. Work from the bottom up. Persevere, as this material does not stick well and needs to be patted into place. When set apply a second coat to achieve a total vermiculite render thickness of around 50mm.

Step - 24

Make a mix of 4 parts sharp sand, 1 part cement and oxide colouring (we used yellow) to make a render mix. Add a bonding agent (such as Bycol) and waterproofing liquid (such as Silasec) to the mixing water to aid in adhesion and to waterproof the render. Apply in two or three coats using a timber float to build a total thickness of 30mm, giving the oven an adobe look. Let set and cure for at least a week. We also bagged the recessed panels in the brickwork base.

Step - 25

Give the oven a final clean up, and if necessary remove mortar smears with a little diluted hydrochloric acid after thoroughly dampening down the brickwork. When first using the oven, start with a small fire to gradually dry out the building materials. Do this a couple of times as it takes a while to dry out the bricks. Only when the bricks are thoroughly dry can you build a fire to bring the oven up to operating temperature. When the internal bricks go white, you know the temperature for cooking has been reached.

Stockists: Pizza oven built by Dean Tolomeo, 0407 432 754. All refractory bricks, mortars, insulation, flue and steel door, Field Furnace Refractories, (02) 9729 1799 or check under Refractories in the Yellow Pages. Table and bench developed and built by Nikos Grammenos, (02) 4751 6190. All outdoor setting materials, Warringah Timbers, (02) 9981 3733 or warringahtimbers.com.au


Ymullaji

Dome wall thickness

The thicker the walls of a wood fired pizza oven the greater the thermal mass the oven wil...

How to clean a brick hearth

What is the best type of bristle brush to clean the brick hearth in my Wood Fired Oven?

Card image cap
How to cook with a wood fired pizza oven

Further information: How to build a pizza ovenCooking a pizza in a pizza oven is always a fun e...

Using castable refractory cement between bricks?

Hi, newbee "mason" here. I have castable high temp mortar that I tried to use to butter between the ...

Card image cap
How to build a pizza oven hearth

Round pizza oven hearthIn a wood fired pizza oven the hearth is the section upon which the...

Card image cap
Purchasing a pizza oven

Further information: How to build a pizza ovenA pizza oven may be either built from raw materials or...

Card image cap
Types of cement

Further information: How to build a pizza ovenWhite cementThere are several ordinary cements in...

Card image cap
How to cook steak in a pizza oven

See: How to cook with a wood fired pizza oven1" (1 inch) = 2.5cm.Thickness1/2"3/4"1"1 1/4"1 1/2...

Card image cap
How to build a wood fired oven door

Further information: How to build a pizza ovenA door is a useful component of any tradition woo...

Card image cap
How to build a pizza oven shelter

Pizza oven shelterWhen building a pizza oven in an external location, it is important to c...

Card image cap
How to fire a wood fired pizza oven

Further information: How to build a pizza ovenWhen starting the initial fire in the oven be sur...

Card image cap
Fire bricks

Fire bricksFire bricks are an essential material in the building of a long-lasting, effective pizza ...

Card image cap
How to clad a pizza oven

Further information: How to build a pizza ovenCladding of a wood fired oven is the final layer ...

Card image cap
Build a pizza oven foundation out of brick

Building a pizza oven foundation out of brick starts with preparing the location. Fir...

Card image cap
Types of wood fired pizza ovens

Further information: How to build a pizza ovenBarrel VaultBarrel vault ovens are usually made o...

Card image cap
Common problems with pizza ovens

Further information: How to build a pizza ovenWhy my oven is not hot enough?The temperature pot...

Card image cap
Insulating dome pizza oven

The materials you use to build your oven determines how long the oven will last. The material of the...

Card image cap
Sourcing materials for building a wood fired oven

Sourcing materials for building a pizza oven can be difficult due to the types of material...

Card image cap
Pizza oven plans

A number of building plans exist due to the wide range of techniques by which a wood fired pizza ove...

Card image cap
What is oven cladding

Oven cladding is the process of applying a mortar or mud material to a wood fired oven to create a t...

Card image cap
Wood fired pizza oven building plans

Traditional wood fired ovens are notoriously challenging and fun to construct, and unique in charact...

Card image cap
History of pizza ovens

Wood-fired pizza ovens have long been existent for thousands of years. This type of oven has be...

Card image cap
Igloo dome vs barrel vault dome pizza ovens

Generally the determination of building an igloo dome or barrel vault pizza oven...

Card image cap
How to Build a Pizza Oven

A traditional wood-fired pizza oven, or more commonly known as masonry oven, is a type of ...

Card image cap
Building plans for a 42 inch igloo brick pizza oven

42inch pizza ovenBuilding plans PDFBuilding plans for a 42 inch igloo brick pizza oven.pdfFurther in...

Card image cap
How to install pizza oven insulation

Further information: How to build a pizza ovenThe insulation of a wood fired oven in its constr...

Card image cap
Different Bricks and quality testing methods

How to test good quality bricks!Brick is one of the important materials in making pizza oven. There ...

Card image cap
Fire brick

Fire bricksFire bricks are an essential material in the building of a long-lasting, effective pizza ...


More Forum Threads